The Firefox Add-on “ContextSearch” lets you highlight text in a web page and then use search tools of your choice to search on the term. I have it set up with Google, Wikipedia (choose English or German), Google Maps and some other tools that came with it.
Goodreads is a website that lets users review books. It and wikipedia are usually my first stops when looking up a book.
Today it occurred to me that it would be nice to also use it to look up books on Goodreads.
I set up a new search engine option using the URL https://www.goodreads.com/search?q=
I got that URL by searching for a book on the site, then taking the URL https://www.goodreads.com/search?utf8=%E2%9C%93&q=small+angry+planet&search_type=books&search%5Bfield%5D=on
and stripping off everything after the “search?”.
The fact that this works makes me think it might work for other search tools as well.
I use masking tape a lot to label stuff, tack stuff in place mark a spot when measuring. And of course for masking.
Finding the start of the roll is a nuisance.
So, I put some in a tape gun and mounted it upside down so it’s a dispenser when stored.
I was not sure at first how well this would work since the tape is mounted sticky side up. I have had this up for more than 6 months now, and sometimes the tape isn’t used in weeks. I am pleasantry surprised how well it still works after that.
I have been searching for new shin pads for soccer for a while. Most that are on the shelves here are thick and and awkward. I finally got some anyway (Nike Mercurial Lite), but hated them because they were way too wide in the bottom.
Then someone mentioned that hers were intended to be heat molded. I figured the chances of mine being a thermoplastic were pretty good. So, I put them into a pot of boiling water for about a minute and pushed them into shape over a pair of socks. They molded quite easily. Wrapped a velcro strap around them while they cooled down, and they now seem to hold their shape nicely.
The finish that used to be shiny on the outside is now a bit wrinkly; this may actually be a good thing, maybe it will make them less slippery.
Will have to see if they last and keep their shape.
Wikidata is a sister project to Wikipedia that encodes much of the information on Wikipedia into discrete data values that can be queried.
I needed to document some ICD10 diagnoses and wanted to add links to Wikipedia as part of that. I did not know the actual names of the articles on Wikipedia, though. Manually, I could have found them using a search, but that would be a lot of work for >1700 diagnoses.
I read about Sichuan Pepper in Cooking for Geeks a long time ago. I have been wanting to try a dish with them for a long time. Recently there was a post on the Winnipeg SubReddit that mentioned that the Golden Loong restaurant uses them. Yesterday I finally got to try their Kung Pao Chicken with fresh sichuan peppercorns. The basic taste is lemony. More importantly, they are tingly and change the flavour of everything in the part of your mouth where they burst, including the water you drink after. Of the four of us there, one hated the sensation, one didn’t much like it, and the other two liked it at least for the intensity of the sensation. I’d have it again. Very neat experience, and one thing gone from the geeky bucket list :-)
An organization I am involved with does its internal communication and broadcasts exclusively through Slack. In my mind, Slack is “evil” because it lets communication in but doesn’t seem to provide tools to let communication out. For example, they don’t provide RSS feeds. I do most of my daily surfing through RSS feeds.
Today I figured I should look into this further and posted the question on the Slack Reddit. Someone suggested I could do this through Zapier. I had never heard about them: they provide integration between different web apps. Sure enough, 15 minutes of tinkering later I now have an RSS feed from that Slack channel.
Update: It turned out very quickly that Zapier will only let you do so many updates for free. It doesn’t even reset over time. So, unless you are willing to pay for this, don’t bother with them.
Things should not be so complicated, but when they are, it is good to have a tool like that!
I was tuning up a pair of scicssors and had to tweak the bend in one of the blades slightly. I have jaw protectors for my bench vise, but needed something to hold the other side without marring the metal. So, I made jaw protectors for some slip joint pliers out of a thick sheet of brass left over from an earlier project.